![]() ![]() The 3Dconnexion product portfolio includes the following devices: The entire 3Dconnexion product line will be compatible with the release of xDesign. The combination of 3Dconnexion’s product line with xDesign’s collaborative platform will provide an optimal design experience for those working in CAD.” “Users of 3Dconnexion’s devices are well aware of the benefits, such as increased productivity, improved user health and facilitated intuitive and user-friendly workflows. “We are thrilled to collaborate and enable xDesign-3Dconnexion compatibility across our product line,” said Ken Denton of 3Dconnexion. The eagerly anticipated update takes effect following SOLIDWORKS World and will be previewed during the conference in Dallas, TX, February 10 – 13, 2019 at the Kay Bailey Hutchison Convention Center. xDesign, based on Dassault Systèmes’ 3DEXPERIENCE platform, is SOLIDWORKS’ new CAD and collaboration tool, run entirely in browser with no installation necessary. Norwalk, CT – 3Dconnexion, supplier of high-performance input devices for CAD professionals, announced today that 3Dconnexion devices will be compatible with SOLIDWORKS’ xDesign modeling solution, in response to high demand from early xDesign users. Want to join us? Sign up for the SOLDWORKS xDesign Lighthouse at: just click on the banner below.Update to Take Effect Following SOLIDWORKS World. Nine minutes of xDesign use and a little shy of eight hours of 3D print time I should have something to take to the party! A minute or so later I was sending the print from Cura to the Ultimaker 3 on my desk over the network. I wanted to use the 3D Cloud Print functionality but I hadn’t got the code from the Sindoh printer in the Fab Lab so I went for the old-fashioned method and downloaded the STL. Just to make sure I hadn’t overlooked any of the areas that may have needed supports, I took it into the 3D Print setup in xDesign and everything looked good. Then it just wouldn’t be complete without the company logo! ![]() Then I rounded things off with a few fillets. ![]() To get around that I simply added an angle where the lips dropped off and faded back on. This would have required supports also as I wanted the home button or bottom of the screen to be accessible while the phone is on the stand. Next was the lip to stop the phone sliding off. This was very easy as I could just grab the center of those shapes and check them inside the diamond cut-out shape. However, I went for a diamond-shaped hole for the charger cable to echo that of the diamonds on the front and back and then quickly drew a slot shape for a lightning cable and a rectangle for micro-usb and made sure they fitted fully inside the diamond. To stop the phone from sliding off and allow the charger to go in the bottom of the phone, I needed to add a couple more features, which would have usually required supports. All nice, quick and easy with a very familiar workflow to that in SOLIDWORKS 3D CAD. This mean no supports to clean out after the build. Unfortunately, there’s no ellipse tool so I had to go for diamond-shaped cut-outs. Next was to reduce the amount of material to speed up the printing time even more. To keep print time down, I would print it on its side as this would be the minimum Z height. I started with an almost-closed isosceles triangle-shaped extrude, with a ledge for the phone to sit on. Time was of the essence so I did a quick search for some examples and found a nice bent acrylic version with a circular hole in the back for the charging cable and a lip to keep the phone on the stand but with space for the cable in the bottom. Ok, so it isn’t very imaginative but if you have any better suggestions, let me know in the comments and I will give it a try. I fired up xDesign from the 3D quadrant of the 3DEXPERIENCE Compass and started from scratch on something every executive needs: a charging stand for their phone. After all, today is Thursday and the party is tomorrow! To up the ante somewhat, and also save myself some post-processing time, I would design it so it could be printed as quickly as possible and needing no support structures. It would be a nice icebreaker, and I thought it would be a good project to try out SOLIDWORKS xDesign on my Chromebook. I couldn’t go empty-handed so I thought I would 3D print something to give to her boss. This Friday I was invited to my wife’s work’s BBQ.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |